Zanussi ZGF640ITX Uživatelský manuál

ZGF 640 ITGas hobInstructionbookletIEGB

10Carefully supervise cooking with fat or oil, since these types offoodstuff can result in a fire, if over-heated.The stainless steel can becometarnis

11Before any maintenance or cleaning can be carried out, youmust DISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is s

12Pan SupportsPan SupportsPan SupportsPan SupportsPan SupportsWash the pan supports using hot soapy water. If necessary, a paste cleaneror a soap impr

13Something Not Working?If the hob is not working correctly, please carry out the following checksbefore contacting your local Service Force Centre.

14OVERALL DIMENSIONS Width: 594 mmDepth: 510 mmCUT OUT DIMENSIONS Width: 560 mmDepth: 480 mmSUPPLY CONNECTIONSGas:R 1/2 inch (1/2 inch male) Rear righ

15Gas burnersGas burnersGas burnersGas burnersGas burnersBURNER RAPID SEMI-RAPIDAUXILIARYPOSITION MAX MIN MAX MIN MAX MINNOMINAL THERMAL POWER

16Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th

17600 MIN.LocationLocationLocationLocationLocationThe hob may be located in a kitchen, akitchen/diner or bed sitting room, butnot in a bathroom or sho

18Gas ConnectionConnection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steelor copper.The connection should be suitable for

192Building over a kitchen unitwith doorProper arrangements must be taken indesigning the furniture unit, in order to avoidany contact with the bottom

2Thank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceT

20Fitting the Hob into the WorktopCarry out the building in of the hob as follows:• place the seals supplied with thehob on the front edge of the cuto

21Electrical ConnectionsAny electrical work required to install this hob should becarried out by a qualified electrician or competent person, inaccord

22Wiring diagramPermanent ConnectionPermanent ConnectionPermanent ConnectionPermanent ConnectionPermanent ConnectionIn the case of a permanent connect

23Fault FindingPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Syst

24A. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKAppliance must be elect

25Check gas supply atburnerIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgn

26CommissioningWhen the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below.1)

27Conversion from Natural Gas to LPGIMPORTANTThe replacement/conversion from natural gas to LPG should only beundertaken by a competent person.It is i

2839712-7901 04/09 R.Awww.zanussi.co.uk

3ContentsImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety Information.

4Important Safety InformationYou MUST read these warnings carefully before installing or usingthe hob. If you need assistance, contact our Customer Ca

5ServiceServiceServiceServiceServicez This hob should only be repaired or serviced by an authorised ServiceEngineer and only genuine approved spare pa

6Description of the Hob1. Hob Top2. Auxiliary Burner3. Semi-rapid Burner4. Rapid Burner5. Control knobs425133

7INSTALLATIONAny gas installation must be carried out by a registeredcompetent person, and in accordance with existing rules andregulations.The releva

8Lighting the burnersLighting the burnersLighting the burnersLighting the burnersLighting the burnersFor easier lighting, proceed before putting a pa

9Do not keep the control knob pressed for more than 15seconds.If the burner does not light even after 15 seconds, releasethe control knob, turn it t